Washington School Bus Practice Test

Practice test questions — School Bus

1. What are the 'danger zones' around a school bus?

   • Only the area in front of the bus
   • 10 feet in front, 10 feet on each side, 10 feet behind, and an additional area where the driver cannot see directly — students must stay out of these areas ✓
   • Only the back of the bus
   • There are no danger zones

   The 'danger zones' are areas immediately around a school bus where students are at greatest risk of being struck or run over. The zones extend approximately 10 feet from the front, sides, and rear of the bus. The most dangerous area is immediately in front of and beside the bus — the bus's mirrors a…

2. What types of mirrors does a school bus typically have, and what does each show?

   • Just two side mirrors
   • Flat side mirrors (true-distance side view), convex side mirrors (wider angle), and cross-view mirrors (visibility immediately in front of the bus and along the sides) ✓
   • Only a rearview mirror
   • No mirrors are required

   School buses have an extensive mirror system because of the special need to see small students near the bus. Flat side mirrors (also called West Coast or plane mirrors) show side and rear traffic at true distance. Convex side mirrors (or 'spot' mirrors) show a wider angle, including blind spots imme…

3. When picking up students at a stop, what should the driver do?

   • Approach quickly to save time
   • Approach slowly with warning lights activated, stop where students can board safely on the curb side, activate the red flashing lights and stop arm, watch all mirrors for students, and only proceed when all students are seated and no students are near the bus ✓
   • Stop in the middle of the road
   • Pull onto the shoulder

   School bus pickup procedure: approach the stop slowly with the amber (yellow) warning lights activated about 200 feet before the stop, signaling that the bus is about to stop; stop in a safe location where students can board from the curb side (never from the traffic side); activate the red flashing…

4. When unloading students at a stop, what is the safest procedure?

   • Quickly drop off students and continue
   • Stop in the right lane (do not pull over to shoulder unless required), activate red lights and stop arm, have students remain seated until the bus is fully stopped, instruct students to walk 10 feet in front of the bus before crossing (if crossing is needed), and verify all students are clear before driving away ✓
   • Have students get off while the bus is still moving slowly
   • Drop students in the middle of the road

   School bus unloading procedure: stop in the right lane of the road (pulling onto a shoulder is generally avoided as it complicates the stop-arm law); activate red flashing lights and stop arm; require students to remain seated until the bus is fully stopped; instruct students who must cross the road…

5. What is the 'student count' procedure?

   • Counting students only at the start of the day
   • Mentally counting students as they unload at each stop, then visually verifying all students are at a safe distance before driving away ✓
   • Counting fares
   • Counting bags

   The student count is a critical safety procedure: as students unload, the driver mentally counts the number of students leaving the bus, then before driving away looks to verify that all those students are clearly visible at a safe distance (at least 10 feet) from the bus. If any student is missing …

6. When should the driver evacuate a school bus in an emergency?

   • Always, regardless of conditions
   • Only if remaining on the bus is more dangerous than evacuating — for example fire, smoke, water hazard, or risk of being struck by another vehicle ✓
   • Never
   • Only in good weather

   School bus evacuation is a major undertaking with young children and should be done only when staying aboard is more dangerous than evacuating. Conditions that require evacuation: fire or smoke aboard; danger of fire (fuel leak, electrical fire signs); risk of being struck (bus stopped on tracks, in…

7. What is the standard procedure for evacuating a school bus through the front door?

   • Have students run out as fast as possible
   • Have students leave their belongings, exit one at a time starting with the front, walk (do not run), assemble at a safe distance away from the bus and away from traffic, and do a head count ✓
   • Open all doors and have students choose
   • Have students stay on board

   Standard front-door evacuation procedure: order all students to leave their belongings behind (slower and creates obstacles); have them exit one at a time, walking not running, starting from the front rows and proceeding back; direct them to assemble at a designated safe distance from the bus (typic…

8. What is the standard procedure for evacuating through the rear emergency exit?

   • Open the door and let students figure it out
   • Have students exit through the rear door, with the driver directing students to sit down at the door, push out, and step off into a safe area; older students often help younger ones ✓
   • Push students out without instruction
   • Open the rear door but stay on the bus

   Rear emergency exit evacuation: open the rear door (or roof hatch in some buses); have students sit down at the door, slide forward to the door opening, and step off; the driver or a designated student helper assists each student. Stepping down from the rear of a bus is awkward; the seated-and-slide…

9. What is the standard procedure for crossing railroad tracks in a school bus?

   • Approach at posted speed
   • Stop 15 to 50 feet before the nearest rail, turn off heat/AC and noise sources, open the entry door, look and listen in both directions, and only proceed when sure no train is approaching — without shifting gears while crossing ✓
   • Slow down only if a train is visible
   • Use the same rules as a passenger car

   School bus railroad crossing procedure is one of the most heavily regulated procedures in the entire CDL: stop 15 to 50 feet before the nearest rail; turn off the heater, AC, fan, and any other noise sources; open the entry door (and the driver's window) to be able to hear an approaching train; look…

10. Why must the driver turn off noise sources before listening at a railroad crossing?

    • To save fuel
    • Engine and accessory noise can mask the sound of an approaching train; listening is part of verifying no train is coming ✓
    • Only for student comfort
    • Noise sources do not need to be off

    An approaching train can often be heard before it is clearly seen, especially around curves or in fog. Engine, heater, AC, and student noise inside the bus can mask the sound of the train's horn or the rumble of approaching cars. Turning off the heater/AC fan, having students quiet down, and opening…

11. What is the driver's responsibility for student behavior on the bus?

    • The driver has no responsibility for student behavior
    • The driver is responsible for maintaining order, enforcing safety rules, and ensuring student behavior does not distract from safe operation; serious problems should be reported to school authorities ✓
    • Only academic performance
    • Only attendance

    School bus drivers are responsible for student behavior to the extent it affects safety: students must remain seated facing forward; no horseplay, fighting, or throwing objects; no shouting that distracts the driver; no objects that pose a hazard (large items in aisles, sharp objects). Persistent or…

12. How should the driver respond if students are fighting on the bus?

    • Continue driving and ignore the fight
    • Pull the bus over to a safe location, do not physically intervene, address the situation calmly, and call for assistance if needed before proceeding ✓
    • Physically separate the students
    • Yell at the students until they stop

    If students are fighting, the driver's first action is to pull the bus over safely (not the shoulder of a busy highway unless no alternative). Stopping eliminates the driving distraction and reduces the chance of a crash. Address the situation calmly with verbal direction first. The driver should no…

13. What is the driver's role in addressing bullying on the bus?

    • Bullying is not the driver's concern
    • Drivers must recognize and report bullying, intervene appropriately when safe to do so, and not allow bullying to occur in their presence ✓
    • Only physical bullying matters
    • Only the school can address bullying

    School bus drivers are often the first to observe bullying because the bus is a relatively unsupervised environment. Drivers should recognize bullying behavior — verbal harassment, exclusion, name-calling, physical threats, hazing — and address it. Verbal intervention from the driver ('that's enough…

14. What is the driver's response to a student reporting bullying or harassment?

    • Tell the student to ignore it
    • Take the report seriously, listen carefully, document the report, and pass it to school administration for action ✓
    • Confront the alleged bully directly
    • Punish the reporter for complaining

    When a student reports bullying or harassment to the driver, take it seriously. Listen to the student calmly without judgment; document the report with details (who, what, when, where, witnesses); reassure the student that the report will be acted on; pass the report to the school administration as …

15. What do the amber (yellow) flashing lights on a school bus signal?

    • The bus is broken down
    • The bus is about to stop to load or unload students; other drivers should slow down and prepare to stop ✓
    • The bus is celebrating
    • Pass with caution

    The amber flashing lights on a school bus warn other drivers that the bus is about to stop to load or unload students. They are typically activated about 200 feet before the stop. Other drivers should slow down and prepare to stop; in most states it is illegal to pass a school bus showing amber warn…

16. When are other vehicles required to stop for a school bus with red lights flashing and stop arm extended?

    • Only the vehicle directly behind the bus
    • On undivided roads, all vehicles in both directions must stop; on divided roads, typically only vehicles in the same direction must stop. Always check state-specific rules ✓
    • No other vehicles need to stop
    • Only buses must stop for other buses

    On an undivided road, all traffic in both directions must stop when a school bus has red lights flashing and stop arm extended — this protects students who may cross the road. On a divided road (with a physical median or barrier), generally only traffic in the same direction as the bus must stop; tr…

17. When should the driver use the front-of-bus crossing procedure?

    • Only when students are crossing in a crosswalk
    • Whenever students must cross the road in front of the bus to reach their destination after unloading — they should walk 10 feet ahead of the bus, look both ways, make eye contact with the driver, and cross only when the driver signals it is safe ✓
    • Never
    • Only at intersections

    The front-of-bus crossing procedure is a critical safety practice. When students must cross the road after unloading to reach their home or destination, they should: walk forward to a point at least 10 feet in front of the bus where the driver can see them clearly; stop and look both ways for traffi…

18. How often should school bus drivers practice evacuation drills?

    • Never
    • School districts typically conduct evacuation drills periodically (often twice yearly or per state requirement); drivers should be familiar with the procedure and able to execute it without rehearsing in an emergency ✓
    • Only when a new student is added
    • Only at the start of the school year

    Evacuation drills are typically conducted at least twice yearly in most school districts, often once at the start of the school year and once at mid-year. Students learn the procedure: where the emergency exits are, how to evacuate quickly and orderly, where to assemble after exiting. Drivers practi…

19. Where is the most dangerous area for students around the bus?

    • Behind the bus
    • Immediately in front of and beside the bus — these areas have the largest blind spots, and most student fatalities occur in these zones ✓
    • Far away from the bus
    • Inside the bus

    The most dangerous area for students is immediately in front of and immediately to the right side of the bus. The driver's seat is high above the ground and the front of the bus is several feet ahead of the windshield, creating a blind spot where a young student can be invisible to the driver. The r…

20. What endorsement does a school bus driver need?

    • Only the standard CDL
    • Both the P (Passenger) and S (School Bus) endorsements, with the S endorsement requiring an additional written knowledge test, road skills test, and (in most states) a background check ✓
    • Only the S endorsement
    • Only the P endorsement

    School bus drivers need both the P (Passenger) and S (School Bus) endorsements. The P endorsement covers passenger transport generally; the S endorsement adds school-bus-specific knowledge (danger zones, loading/unloading procedures, railroad crossings, evacuations, student management, anti-bullying…

21. How far in front of the school bus should students cross the road after being discharged?

    • Directly in front of the bumper
    • At least 10 feet (approximately 3 giant steps) in front of the bus — far enough that the driver can see the student clearly in the cross-view mirror before the student reaches the far side of the road ✓
    • Behind the bus, where there is less traffic
    • Students can cross anywhere they choose

    THE 10-FOOT CROSSING RULE is a critical school bus safety standard. REASON FOR THE DISTANCE: The driver's primary mirror for monitoring crossing students is the cross-view or convex mirror mounted at the front corners of the bus; for a student to be visible in this mirror, they must be at least 10 f…

22. A student exits the bus and drops something near the front wheel. What should the driver do if the student bends down to pick it up?

    • Honk the horn and drive around the student
    • Do not move the bus under any circumstances; the student has entered the front danger zone directly in front of and around the wheel; the driver should open the window and instruct the student to stand up, back away from the bus, and make eye contact before the driver can proceed ✓
    • Wait for the student to pick up the item and assume it is safe to proceed
    • The front crossing arm will protect the student

    A STUDENT IN THE FRONT DANGER ZONE — especially bent over or on the ground — represents one of the highest-risk situations in school bus operation. WHAT MAKES THIS SO DANGEROUS: The student is now low to the ground, potentially under or very close to the front wheels; the driver's view of this posit…

23. A school bus driver approaches a railroad crossing and finds the crossing gates are up and no lights are flashing. Must the driver still stop?

    • No stop is required if gates are up and lights are not flashing
    • YES — a school bus carrying students must stop at ALL railroad crossings regardless of gate position, light status, or train visibility; the mandatory stop is a federal requirement with no exception for absence of warning signals ✓
    • Stop only if a train can be heard
    • Stop only at gated crossings when gates are down

    SCHOOL BUS RAILROAD CROSSING RULES are the most stringent of any vehicle class. ABSOLUTE REQUIREMENT: Federal law (49 CFR 392.10) requires school buses carrying passengers — ANY passengers, even one student — to stop at ALL railroad crossings without exception. NO EXCEPTIONS FOR: Gates being up or a…

24. Under what conditions should a school bus driver initiate an emergency evacuation of students?

    • Only when the bus is on fire
    • When remaining on the bus is more dangerous than evacuating — fire or smoke, hazardous material leak, structural damage threatening collapse, being in water or at risk of entering water, or if the bus is blocking traffic in a dangerous location with no ability to move ✓
    • Only when a student requests evacuation
    • Only under direct instruction from dispatch

    EMERGENCY EVACUATION DECISION requires rapid judgment: which is more dangerous — staying on the bus or evacuating? EVACUATE WHEN: FIRE or SMOKE on the bus — any fire on a school bus is cause for immediate evacuation; school bus fires can accelerate extremely rapidly; post-crash fire is a specific sc…

25. What should a school bus driver do if a student refuses to follow bus safety rules?

    • Stop the bus and force the student off at an unscheduled location
    • Address the behavior calmly and firmly; warn the student; document the incident; report to the school administration — the driver cannot physically force a student to comply, but the school has authority to address the behavior; in extreme cases where safety is threatened, stop safely and call for assistance ✓
    • Ignore the behavior to avoid confrontation
    • Drive faster to get to the destination sooner

    STUDENT DISCIPLINE ON THE BUS requires the driver to be both the operator and the safety authority without being able to use physical force or leave their seat. THE DRIVER'S TOOLS: VERBAL — calm, firm, clear instructions; address the student by name when possible; explain why the rule exists (safety…

26. What are the four danger zones around a school bus and why is the right-side zone considered most dangerous?

    • There is only one danger zone — directly in front
    • The four zones are: FRONT (immediately in front, blind spot below windshield), LEFT SIDE (along the driver's side), RIGHT SIDE (along the passenger side), and REAR (directly behind). The RIGHT side is most dangerous because it has the largest blind spot and students typically board and exit from this side — most fatal school bus pedestrian accidents involve students struck on the right side ✓
    • Danger zones are only relevant for the rear of the bus
    • The rear is the most dangerous zone because of following traffic

    THE FOUR DANGER ZONES create a ring of risk around the school bus that the driver must actively manage every time students are loading or unloading. FRONT ZONE: Extends approximately 10 feet from the front bumper; students crossing cannot be seen if within this zone; the front crossing arm helps but…

27. Before opening the school bus doors at a stop, what must the driver verify?

    • That the radio is turned off
    • The bus is completely stopped; the parking brake is set; traffic in all directions has stopped and students can cross safely; check all mirrors including cross-view mirrors; the area is free of hazards before allowing students to exit ✓
    • Only that the bus is stopped
    • That all students are standing and ready

    PRE-DOOR-OPENING VERIFICATION is the critical moment where driver attention determines whether students will be safe during the loading/unloading process. COMPLETE STOP AND BRAKE: The bus must be completely at rest with the parking brake set — never open doors while still rolling or before the brake…

28. A driver witnesses one student threatening another student on the bus. What is the driver's responsibility?

    • Ignore it — student conflicts are not the driver's concern
    • Address the behavior safely: use verbal intervention from the driver's seat if possible; document the incident; report it immediately to school administration when the route is complete; if physical safety is threatened and the bus cannot safely move, stop and call for assistance ✓
    • Stop the bus and physically separate the students
    • Turn up the radio to drown out the conflict

    BULLYING AND HARASSMENT on school buses falls under the driver's responsibility to maintain a safe environment for all students. FEDERAL AND STATE CONTEXT: Virtually every state has anti-bullying laws that apply to school transportation; school districts have policies requiring staff (including driv…

29. After evacuating students from a school bus due to an emergency, where should students be directed to assemble?

    • Near the roadway for easy access by emergency vehicles
    • At least 100 feet from the bus (or further from hazardous materials or fire), upwind if there is smoke or hazardous materials, on the far side of any physical barriers from the hazard, and away from traffic lanes — a designated adult (or designated student) should count and account for every student ✓
    • On the opposite side of the road
    • Students should disperse to the nearest houses

    POST-EVACUATION ASSEMBLY LOCATION is critical because evacuating students from the bus is only the first step — students in the roadway or near the hazard are still in danger. ASSEMBLY LOCATION CRITERIA: DISTANCE from the bus: at least 100 feet as a minimum; farther if the situation involves fire (r…

30. What is the purpose of the school bus's amber flashing lights, and when should they be activated?

    • Amber lights are used only in bad weather
    • Amber lights warn approaching traffic that the bus is preparing to stop and load/unload students — activate 200 feet (in city) to 400-500 feet (on highway) before the stop to give drivers time to slow and prepare to stop for the red lights ✓
    • Amber lights indicate the bus needs to be passed on the left
    • Amber lights replace the need for a stop sign arm

    THE AMBER FLASHING LIGHT SEQUENCE is a critical warning system that gives approaching traffic advance notice before the bus activates its mandatory red stop lights. TIMING REQUIREMENTS: Most states specify activation distances: URBAN/SUBURBAN areas (under 35 mph): activate approximately 100-200 feet…

31. A student must cross the road after exiting a school bus. Before the student can cross, what must happen?

    • The student can cross whenever they are ready
    • The driver must extend the stop arm and activate red flashing lights; the student must walk at least 10 feet in front of the bus (to enter the driver's cross-view mirror range); make eye contact with the driver; receive the driver's signal or nod to cross; then check traffic in both directions while crossing ✓
    • Students may cross behind the bus
    • The driver can proceed as soon as the student exits

    THE CROSSING SEQUENCE protects students from the two primary danger scenarios: being struck by the bus itself (by staying visible in mirrors); and being struck by passing traffic (by requiring traffic to stop before crossing begins). REQUIRED SEQUENCE: Student exits → walks FORWARD (never behind) al…

32. What must a school bus driver do differently from other commercial vehicle drivers at a railroad crossing?

    • Nothing different — all rules are the same
    • School buses carrying passengers must stop at ALL railroad crossings, open the door to listen for trains, and must never stop a school bus with students on the tracks for any reason — these rules are stricter than for other CMVs in that the door-opening requirement is usually mandatory for school buses even where it is optional for other buses ✓
    • School buses may cross at normal speed
    • School buses are exempt from railroad crossing stops

    SCHOOL BUS RAILROAD CROSSING RULES are among the strictest in federal transportation law because of the cargo: children. MANDATORY REQUIREMENTS: (1) STOP — at ALL railroad crossings, every time, without exception for signal status or apparent train absence; (2) OPEN DOOR — open the service door (fro…

33. What must a school bus driver verify before releasing the parking brake and pulling away from a school bus stop?

    • That the schedule shows it is time to leave
    • All of the following: (1) all students who were exiting have cleared the danger zones and reached a safe location; (2) all students crossing the road have completed the crossing and are on the far sidewalk or shoulder; (3) all mirrors show no students near the bus; (4) the stop arm is fully retracted; (5) red lights have extinguished ✓
    • Only that the door is closed
    • Only that the stop arm is retracted

    DEPARTURE SEQUENCE — every step must be completed before movement: STUDENT CLEARANCE: All exiting students must be visible in a safe location (sidewalk, driveway, away from the roadway) — not just 'probably there' but actually visible; CROSSING CLEARANCE: If any students crossed, they must be visibl…

34. A student on the bus is having a serious medical emergency (seizure). The bus is moving at 40 mph on a highway. What should the driver do?

    • Stop the bus immediately in the traffic lane
    • Pull safely to the highway shoulder as quickly as safely possible; call 911 with exact location; do not leave the driver's seat until safely stopped; assign a responsible student to stay with the affected student; follow emergency response protocol for the specific situation ✓
    • Continue to the school — it is closer than a hospital
    • Ask other students to handle it

    STUDENT MEDICAL EMERGENCY — on a moving highway bus: PRIORITY: Vehicle safety first — stop in a safe location before any other action; a moving bus crash would injure all students including the one with the emergency; SAFE STOP: Move to the shoulder as quickly as safely possible — this may be differ…

35. When evacuating a school bus after a crash, why should students NOT be directed to cross the road immediately after exiting?

    • Crossing the road is always permitted
    • Post-crash traffic may not be stopped — emergency vehicles responding to the crash, rubbernecking drivers slowing unexpectedly, and confused traffic patterns create unpredictable hazards; students should be moved to a safe assembly area on the same side of the road unless a greater hazard (fire, structure collapse risk) makes crossing unavoidable ✓
    • Students can always cross safely during an emergency
    • Crossing rules only apply during normal school bus stops

    POST-CRASH ROAD HAZARDS: The immediate area around a crashed school bus is a secondary crash hazard zone. Drivers approaching the scene may: be slowing suddenly creating rear-end risk; be distracted looking at the crash; be responding emergency vehicles driving urgently; or be stopped and creating p…

36. What are the 'danger zones' around a school bus?

    • Only the area behind the bus
    • The areas on all sides of the bus where children are in the most danger of being hit — extending up to 10 feet in front, 10 feet on each side, 10 feet behind, and the area immediately around the bus where the driver may not be able to see children ✓
    • Only the inside of the bus
    • There are no danger zones

    SCHOOL BUS DANGER ZONES: The areas immediately around the bus where children are at the greatest risk of being struck — and where the driver may NOT be able to see them. EXTENT: Up to 10 feet in FRONT of the bus; 10 feet on the LEFT and RIGHT sides (especially around the entrance door and rear wheel…

37. When students are crossing the road in front of the school bus, how far in front should they cross?

    • Right at the front bumper
    • At least 10 feet (about 5 giant steps) in front of the bus, so the driver can see them — students should never cross within the danger zone close to the front bumper where the driver cannot see them ✓
    • Behind the bus
    • It doesn't matter

    STUDENT CROSSING DISTANCE: Students crossing in front of the bus must cross at least 10 FEET (about 5 'giant steps') in FRONT of the bus. WHY: A child too close to the front bumper is in the driver's BLIND SPOT — the driver cannot see them from the seated position; crossing 10+ feet ahead keeps the …

38. What should a school bus driver do if a student drops something near the bus while loading or unloading?

    • Tell the student to pick it up quickly
    • Instruct the student to LEAVE the item and signal the driver before retrieving anything — students should never bend down or reach under/near the bus to get a dropped item, as they enter the danger zone out of the driver's sight ✓
    • Ignore it and drive away
    • Get out and pick it up while students board

    DROPPED ITEMS NEAR THE BUS: A leading cause of school bus fatalities — a student drops something (paper, phone, toy) near the bus, bends down to retrieve it, enters the danger zone (often in front of or beside the bus, below the driver's sightline), and is struck when the bus moves. PROCEDURE: Teach…

39. When approaching a school bus stop, what should the driver do with the warning lights?

    • Never use them
    • Activate the alternating amber (yellow) warning lights well before the stop (per state law, often 100-300 feet or 5-10 seconds before), then activate the red flashing lights and stop arm when stopped to load/unload students ✓
    • Only use red lights
    • Use headlights only

    SCHOOL BUS WARNING LIGHT SEQUENCE: AMBER (YELLOW) lights: Activate the alternating amber warning lights BEFORE reaching the stop (per state law — often about 100-300 feet or 5-10 seconds in advance, more on high-speed roads) to warn traffic that the bus is about to stop; RED flashing lights + STOP A…

40. After unloading students, what must the school bus driver do before pulling away from the stop?

    • Pull away immediately
    • Make sure ALL students are completely clear of the bus and the danger zone, count students if possible, check all mirrors, and verify no child is crossing, retrieving an item, or in any blind spot before moving ✓
    • Just check the rear mirror
    • Honk and go

    BEFORE PULLING AWAY: The driver must ensure ALL students are completely safe before moving. PROCEDURE: Verify all students who exited have moved away from the bus and out of the danger zone; ensure any students who crossed have safely reached the other side; count students if you track a count; CHEC…

41. In what situations should a school bus be evacuated immediately?

    • Never evacuate
    • When there is a fire or danger of fire, the bus is in or near water, the bus could be hit by another vehicle, or there is a hazardous materials threat — these situations make staying on the bus more dangerous than evacuating ✓
    • Only at the end of the route
    • Only if the engine stalls

    MANDATORY SCHOOL BUS EVACUATION SITUATIONS: Evacuate immediately when remaining on the bus is MORE dangerous than leaving. ALWAYS EVACUATE for: FIRE or risk/smell of fire (fire spreads fast); the bus is IN or NEAR WATER (or could roll into water); the bus is in a position where it could be HIT by an…

42. What must a school bus driver do at every railroad crossing, even if no train is expected?

    • Speed across
    • Stop within 15 to 50 feet of the nearest rail, turn off radio/fans and open the door and window to look and listen, and cross only when certain it is safe — school buses must stop at all crossings (except those marked exempt) ✓
    • Only slow down
    • Cross without stopping if gates are up

    SCHOOL BUS RAILROAD CROSSING PROCEDURE: School buses must STOP at all railroad crossings (with limited exceptions like exempt or abandoned crossings). PROCEDURE: Approach slowly, activate hazard lights as appropriate; STOP within 15 to 50 feet of the nearest rail; turn off the radio and fans and qui…

43. What is the proper procedure for a school bus driver when students must board at a stop that requires crossing the road?

    • Let them cross whenever
    • Stop the bus with red lights and stop arm activated, ensure traffic has stopped, then signal the students to cross in front of the bus where the driver can see them; the driver maintains control of when students cross ✓
    • Tell students to cross behind the bus
    • Have students cross before the bus stops

    STUDENTS CROSSING TO BOARD: When students must cross the road to board, the driver controls the process for safety. PROCEDURE: Stop the bus, activate red flashing lights and extend the stop arm (legally stopping traffic); ensure all traffic in both directions has actually STOPPED before signaling st…

44. When transporting students with disabilities, what is an important consideration for the school bus driver?

    • Treat all students identically
    • Follow the specific procedures for securing wheelchairs and special equipment, allow extra time for boarding/exiting, use lifts properly, secure students per their needs, and be aware of individual student needs — special-needs transport requires additional training and care ✓
    • Special-needs students don't need accommodation
    • Only the aide is responsible

    TRANSPORTING STUDENTS WITH DISABILITIES: Requires additional knowledge, training, and care. KEY CONSIDERATIONS: WHEELCHAIR SECUREMENT: Properly secure wheelchairs using the securement system (tie-downs at designated points) and secure the student with appropriate restraints; LIFTS: Operate wheelchai…

45. Why must school bus drivers be especially attentive to managing student behavior on the bus?

    • Behavior doesn't affect safety
    • Disruptive behavior can distract the driver and create unsafe conditions; the driver must maintain order so they can focus on driving safely, but should address serious behavior issues by stopping safely rather than dealing with them while driving ✓
    • To make the ride fun
    • Only academic performance matters

    MANAGING STUDENT BEHAVIOR: Student behavior directly affects safety. WHY IT MATTERS: Disruptive behavior (fighting, throwing objects, loud noise, moving around, distracting the driver) can take the driver's attention off the road and create dangerous conditions; students standing or moving while the…

46. What additional items must a school bus driver inspect that are specific to school buses?

    • Nothing additional
    • The stop arm, alternating flashing warning lights (amber and red), crossview/convex mirrors, the service door, emergency exits, and any wheelchair lift/securement equipment — items specific to student safety ✓
    • Only the engine
    • Only the tires

    SCHOOL BUS-SPECIFIC INSPECTION ITEMS (beyond standard CMV and passenger bus checks): STOP ARM: Extends and retracts properly, undamaged; WARNING LIGHTS: Alternating amber and red flashing lights all work; CROSSVIEW/CONVEX MIRRORS: The special mirrors (front fender convex mirrors and crossover mirror…

47. Approximately how many feet should a school bus driver be able to monitor in front of the bus using the crossview mirrors?

    • The crossview mirrors show only the rear
    • The crossview (convex) mirrors are designed to let the driver see the entire front bumper area and the danger zone immediately in front of and to the sides of the bus, where children may be below the direct line of sight ✓
    • They show only the engine
    • They are not useful

    CROSSVIEW (CONVEX) MIRRORS: Mounted on the front corners/fenders of the school bus, angled to show the driver the area DIRECTLY IN FRONT of the bus and along the sides — the danger zone where small children may be below the driver's direct line of sight over the hood. PURPOSE: A child standing close…

48. Why should school bus drivers avoid backing up whenever possible?

    • Backing saves no time
    • Backing a school bus is dangerous because children may be behind the bus in a blind spot; if backing is unavoidable, the driver should use a responsible adult or student monitor to guide them, or get out and check the area first ✓
    • Backing is always safe
    • Children are never near buses

    AVOIDING BACKING A SCHOOL BUS: Backing is one of the most dangerous maneuvers because the area directly behind the bus is a large blind spot where children could be present and unseen. POLICY: Avoid backing whenever possible — plan routes and stops to eliminate the need to back; many districts prohi…

49. How should a school bus driver position the bus when stopping to load or unload students?

    • In the middle of the road at an angle
    • Pull as far to the right as possible, stop completely on as level and straight a section as possible with good visibility, activate the proper warning lights, and position so approaching traffic can see the bus and its signals well in advance ✓
    • Anywhere convenient
    • Partially in a curve to save time

    POSITIONING THE BUS AT A STOP: Proper positioning maximizes safety and visibility. PRACTICES: Pull as far to the RIGHT as safely possible (off the travel lane if a pull-off exists); stop on a section that is as LEVEL and STRAIGHT as possible with GOOD VISIBILITY in both directions (avoid stopping ju…

50. What is the correct response if a school bus driver realizes a vehicle is illegally passing the bus while its red lights and stop arm are activated?

    • Wave the students across anyway
    • Do NOT signal students to cross or proceed until the danger has passed and it is confirmed safe; protect the students by keeping them from crossing into the path of the passing vehicle, and report the violation ✓
    • Speed up to block the vehicle
    • Ignore it

    ILLEGAL PASSING OF A STOPPED SCHOOL BUS: Despite red flashing lights and the extended stop arm legally requiring traffic to stop, some drivers illegally pass — a major danger to crossing students. DRIVER RESPONSE: Do NOT signal students to cross (or hold them if they're about to) until all traffic h…

51. What is the 'danger zone' around a school bus?

    • The area only directly behind the bus
    • The area on all sides of the bus where children are in the most danger of being hit, extending up to about 10 feet in front, 10 feet on each side, and behind the bus, including the area where the driver's view is limited ✓
    • The interior aisle of the bus
    • Only the loading door

    The danger zone is the area immediately around the school bus where students are at greatest risk of being struck, either by the bus itself or by passing traffic, and where the driver's direct vision is limited. It extends roughly 10 feet in front of the bus, 10 feet on each side, and the area behin…

52. Why must a school bus driver use and properly adjust the bus's mirror system before each route?

    • To check the driver's appearance
    • Because the outside flat, convex, and crossview mirrors are the driver's main way to see students and traffic in the danger zones and blind areas around the bus ✓
    • Mirrors are decorative only
    • Only the inside mirror matters

    A school bus has a system of mirrors — flat outside mirrors for distance behind, convex mirrors for a wider view along the sides, and crossview (crossover) mirrors that let the driver see directly in front of and beside the bus. Together they cover the danger zones where children walk and where dire…

53. What is the safe procedure when students must cross the road to board or after leaving the bus?

    • Let them cross behind the bus
    • Have students cross in front of the bus, far enough ahead to stay in the driver's view, and only after the driver signals it is safe, never behind the bus ✓
    • Tell them to run across quickly
    • Allow crossing without any signal

    Students who must cross the roadway should always cross in front of the bus, at least 10 feet (about 10 giant steps) ahead so they remain in the driver's line of sight, and only on the driver's signal that it is safe. They should never cross behind the bus, where the driver cannot see them and where…

54. After unloading students, what should the driver do before pulling away from the stop?

    • Drive off as soon as the door closes
    • Count the students who got off, account for everyone who needed to cross, and check all mirrors and the danger zones to be sure no child is near the bus before moving ✓
    • Honk and accelerate
    • Only check the rear-view mirror

    Before moving away from a stop, the driver must be certain no student is in the danger zone. This means counting the students who unloaded, making sure any who had to cross the road have completed the crossing and reached safety, and scanning all the mirrors and the area around the bus for any child…

55. If a student drops an object near the bus while loading or unloading, what should they be taught to do?

    • Quickly reach under the bus to grab it
    • Never go back for it without the driver's permission and signal, because bending to pick up an item can put the child in the danger zone where the driver cannot see them ✓
    • Pick it up immediately wherever it fell
    • Ask another student to get it

    A dropped item is a classic danger-zone hazard. A child who bends down to retrieve a backpack, paper, or toy near the bus can disappear from the driver's view, including from the crossview mirrors, and may be in the path of the wheels. Students should be taught never to go back for a dropped object …

56. What do the amber (yellow) warning lights and then the red flashing lights on a school bus signal?

    • Amber means stop, red means go
    • Amber flashing lights warn that the bus is preparing to stop to load or unload, and red flashing lights with the extended stop arm require traffic to stop while students load, unload, or cross ✓
    • Both colors mean the bus is parked
    • The lights have no legal meaning

    The amber (yellow) flashing lights are activated in advance to warn other drivers that the bus is about to stop to load or unload students; they are a signal to prepare to stop. When the bus actually stops for students, the driver activates the red flashing lights and extends the stop arm, which leg…

57. In which situations should a school bus driver evacuate the students?

    • Only when the bus runs out of fuel
    • When remaining on the bus would be more dangerous than leaving it — for example, fire or risk of fire, the bus is in or near water, a crash has damaged the bus, or there is a hazard such as a railroad crossing or unstable position ✓
    • Never, under any circumstances
    • Only at the end of the route

    The driver must decide whether evacuating is safer than staying aboard. Mandatory or strongly indicated evacuations include fire or the danger of fire, the bus stalled on or near railroad tracks, a position that could shift into a path of danger (such as on an unstable slope or in water), or a crash…

58. After evacuating students from the bus in an emergency, what should the driver do?

    • Send students home individually
    • Lead or direct students to a safe place a sufficient distance from the bus, away from traffic and other hazards, keep them together, and account for every student ✓
    • Leave them at the bus and seek help alone
    • Let students decide where to go

    Once students are off the bus, the driver must move them to a safe location well away from the bus and from traffic, fuel, fire, or other hazards — the manual commonly references a distance of at least 100 feet in the direction that avoids the danger. Students should be kept together and supervised,…

59. What must a school bus driver do at every railroad crossing?

    • Cross at normal speed if no train is visible
    • Stop within the required distance of the nearest rail, open the service door and driver's window to look and listen, and cross only when sure no train is approaching and the bus can clear the tracks completely ✓
    • Slow but never stop
    • Stop only if a train is in sight

    School buses must stop at every railroad crossing, generally between 15 and 50 feet from the nearest rail, even when no train is visible and there are no gates or lights. The driver opens the service door and the driver's window to look and listen carefully in both directions, because a train can be…

60. Why must the driver open the door and window and stop talking or radio noise at a railroad crossing?

    • To let fresh air in
    • So the driver can listen as well as look for an approaching train, since a train may be heard before it is clearly seen ✓
    • To signal students to be quiet for fun
    • It is not actually required

    At a railroad crossing the driver must both look and listen. Opening the service door and the driver's side window, and quieting the students, radio, and fans, lets the driver hear a train horn or the sound of an approaching train, which can sometimes be detected before the train is clearly visible …

61. How should a driver handle students fighting or behaving dangerously while the bus is moving?

    • Try to break up the fight while driving
    • Pull the bus over to a safe location and stop before dealing with the behavior, because trying to handle it while driving endangers everyone ✓
    • Speed up to reach the school faster
    • Ignore it completely

    If serious misbehavior such as a fight occurs while the bus is in motion, the driver should not try to handle it while driving, which would take attention off the road and endanger all passengers. Instead the driver pulls over to a safe place, stops the bus, secures it, and then addresses the situat…

62. What is the driver's role in maintaining order and discipline on the school bus?

    • Discipline is solely the school's job, not the driver's
    • The driver is responsible for managing student behavior to keep the bus safe — setting clear expectations, watching for problems using the mirrors, and addressing misbehavior so it does not become a driving hazard ✓
    • The driver should let students do whatever they want
    • Only the principal can address behavior

    The driver is responsible for the safety of the students aboard, which includes managing their behavior. Disruptive conduct — students standing, throwing things, crowding the driver, or fighting — can distract the driver and create a serious hazard. The driver sets and enforces reasonable rules, mon…

63. What is the school bus driver's responsibility regarding bullying or harassment among students on the bus?

    • To ignore it as a school matter
    • To recognize bullying and harassment, intervene appropriately to stop it, and report it according to school procedures, because the driver is often the only adult present ✓
    • To punish the victim
    • To let the students resolve it themselves

    The driver is frequently the only adult on the bus and so plays a key role in preventing and responding to bullying and harassment. This means being alert to signs of bullying, intervening to stop it in a calm and appropriate way, supporting the targeted student, and reporting incidents through the …

64. When a student reports being bullied on the bus, how should the driver respond?

    • Tell the student to toughen up
    • Take the report seriously, ensure the student's immediate safety, and document and report it through the proper channels rather than dismissing it ✓
    • Announce it to the whole bus
    • Do nothing unless it happens again

    A report of bullying should always be taken seriously. The driver should make sure the reporting student is safe, respond calmly without publicly embarrassing anyone, and then document and report the incident according to the school district's procedures so that follow-up can occur. Dismissing the r…

65. Why is backing a school bus discouraged, and what must the driver do if backing is unavoidable?

    • Backing is encouraged to save time
    • Backing is dangerous because of the large blind area behind the bus where children may be; if it cannot be avoided, the driver should use a responsible adult or aide as a lookout and back slowly while checking mirrors ✓
    • Backing is perfectly safe at any speed
    • The driver should back quickly to finish fast

    Backing a school bus is strongly discouraged because the area directly behind the bus is a large blind spot where a child could be standing unseen. Routes are planned to avoid the need to back whenever possible. If backing truly cannot be avoided, the driver should use a posted lookout — such as an …